Function Introduction
Installation Instructions
1、Power on the plug.
2、The plug indicator will display green and orange scrolling blinking, and the device will enter the state of configurable network.
3、Then refer to the Aidot APP instructions to add devices.
4、If you need to restore factory settings, you can press and hold the button (>5s) until the red light is on, release the button, The device enters the initial network configuration state again.
LED Indicator
Under normal working state:
LED indicator is solid green— turn on;
LED indicator is off —turn off.
Quick Start Guide
1. Scan the QR code below, or search for“AiDot” in App Store or Google Play.
2.Create an account and sign in.Tap '+' to add the "smart plug".
3.Follow the instructions on the App.
( Note:Please turn on Bluetooth and location. )
For more information about the usage guidelines and FAQs, Please scan the QR code below or visit the website: https://www.aidot.com/s/000f1f.
How to connect you device to other apps that support the Matter protocol, such as Alexa, Apple home, Google home, Smartthings
1. Please use APP scanning function to scan the QR code or manually input the Pairing code below the QR code.
2. Note that the matter QR code on the scanning sticker must be the same as that on the device to be connected to the Internet. As shown in the diagram below.
3. For more information on how to add device to apps that support Matter protocol, please refer to the apps guide of each manufacturer.
Matter QR code posting area:
Warning
1. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications or changes could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, whitch can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment an outlet on a circuit different from that to whitch the receiver is connected.
- Consult the dealer or an experienced radio/TV
To maintain compliance with FCC’ s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.
Cautions
To avoid personal injury and/or possible product damage, the following cautions must be followed:
1. Risk of electrical shock. Disconnect power at fuse or circuit breaker before installing or servicing.
2. To prevent early lamp failure, lamp should only be installed in operating environments ranging between:-20℃ and +40℃(-4°F and +104°F).
3. Suitable for damp locations.
4. Not for use with dimmers.
5. Lamp dims via wireless control and will not operate with a dimmer switch.
6. Not for use in totally enclosed luminaires.
7. Not for use in emergency light fixtures or exit signs.
8. Ensure fixture can support the added weight of the lamp/bulb.
Contact Us
SPRING SUNSHINE TECHNOLOGY CO., LIMITED
FLAT/RM 01-04, 24/F, FU FAI COMMERCIAL
CENTRE, 27 HILLIER STREET, SHEUNG WAN, HK
+1 (877) 770-5727
http://www.linkind.com
Email: service@linkind.com
Made in China
Manufacturer: Leedarson loT Technology Inc.
Adress: No.1511, 2nd Fanghu North Rd, Huli
District, Xiamen, China